The training program will now resume

0 comments

file time: 2008-02-16

filetype:ppt

Click Here To Download...

>  
 
 
 
 

The training program will now resume

 
 
 
 
 

Advanced User Training 

  Now for the interesting part:

  00ield Programming00/b> 

SC PI

 
 
 
 
 

Advanced User Training 

  OK, you asked for it 

  The truth is that once you practice this procedure on an empty channel, you00l find it follows very predictable steps from operation to operation  

[Page Up]                  or      NEXT

 
 
 
 
 

You need to know these things to enter a channel: 

Advanced User Training 

Whether this is to be included in the Scan List    

SC PI 

[Page Up]                  or      NEXT 

Whether this is a Narrow or Wide Band FM channel  
 
 
 
 

[Page Up]                  or      NEXT 

A name for this channel up to 10 characters long  
 
 

[Page Up]                  or      NEXT 

The TX & RX frequencies and subaudable tone  
 
 

[Page Up]                  or      NEXT 

Is this channel already programmed in this radio?  
 
 

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

Let00 first dial up the radio frequency    

Move the EDIT switch to the LEFT this time  
We00l call this the EDIT CHannel selection  
We00l call this the EDIT CHannel selection  

[Page Up]                  or      NEXT 

[Page Up]                  or      NEXT 

The DISPlay switch now shows what it is that you00e changing  - The name display, transmit frequency,     receive frequency,  etc  
 

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

We00l start with the DISPlay switch in the <center>  

r 

[Page Up]                  or      NEXT 

We learned that the DISPlay switch in the (RX) position shows the Receive frequency  
 
 
 

[Page Up]                  or      NEXT 

It00 the same with programming:  You00e programming whatever the DISPlay is set to show at the time  
 
 

[Page Up]                  or      NEXT 

RX

 
 
 
 
 

Advanced User Training 

Being as the DISPlay now shows the RX display, we00l begin programming the Receive frequency  

r 

[Page Up]                  or      NEXT 

The NEXT switch chooses the digit to be edited  
 
 
 

[Page Up]                  or      NEXT 

The SELECT switch makes the number change  
 
 

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

After each digit is SELECTed, go to the NEXT one and keep going until the whole frequency is entered   

r 

[Page Up]                  or      NEXT 

Then, go NEXT even further over to the right, and enter   the CTCSS tone as needed.  
 
 

[Page Up]                  or      NEXT 

That00 it for the Receive frequency  
 

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

Now that we have an RX frequency, we00l do the exact same thing for the Transmit side of the formula   

r 

t 

[Page Up]                  or      NEXT 

[Page Up]                  or      NEXT 

Change the DISPlay switch to the right, to the TX setting  
 
 
 

[Page Up]                  or      NEXT 

Duplicate the frequency and tone which was put into the  RX side (unless the circumstance directs otherwise)  
 
 
 
 

Advanced User Training 

                    The next step is to assign the       Identification, Channel Bandwidth and Scan List inclusion 

                    The next step is to assign the       Identification, Channel Bandwidth and Scan List inclusion 

                    The next step is to assign the       Identification, Channel Bandwidth and Scan List inclusion 

                    The next step is to assign the       Identification, Channel Bandwidth and Scan List inclusion 

SC 

[Page Up]                  or      NEXT 

This step changes items seen in the ID screen, so we       need to switch the DISPlay to ID to make these changes  
 
 
 

[Page Up]                  or      NEXT 

Again, use the NEXT switch to choose which space to    edit, and then SELECT the letter, numeral, symbol needed  
 
 
Again, use the NEXT switch to choose which space to edit, and then SELECT the letter, numeral, symbol needed  
Again, use the NEXT switch to choose which space to edit, and then SELECT the letter, numeral, symbol needed  

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

For the time being, we00l assume all field entries will be in Wide Band format, as used by our other radios at present  
The next choice is for Wide or Narrow FM channel width  

W 

SC 

[Page Up]                  or      NEXT 

Select whether this channel is to be put on the Scan List    for later use in channel scanning  
 
 

[Page Up]                  or      NEXT

 
 
 
 
 

Advanced User Training 

W 

SC 

Finally, return the EDIT switch to the center position  
 
 

[Page Up]                  or      NEXT 

Finally, return the EDIT switch to the center position  
 
 
 
 

Take a moment to go through this informal check-list just once more, to ensure that the equipment is ready for action00.

 

Setting Options 

w SC 

Mission-Ready Check List 

[Page Up]                  or      NEXT 

     
 

                     

       DISPlay Switch = ID                            
 

[Page Up]                  or      NEXT 

       Channel = Air to Ground

   or as directed by your local command 

[Page Up]                  or      NEXT 

SCAN Switch = Normal   

(Not Scanning At This Time) 
 
 

[Page Up]                  or      NEXT 

Guard1/Guard2 Switch = G2

or as directed by local command 

[Page Up]                  or      NEXT 

Verify that you left : 
 

                                                             

                  POWER = HI    
 
 

[Page Up]                  or      NEXTrt 

          TONES = ON 

          

[Page Up]                  or      NEXTrt 

    EDIT Switch = <Centered> 
 
 

[Page Up]                  or      NEXTrt

 
 
 
 
 

Final Practical Review 

  00nd now for some practical review of setings00 

Page Up                    or      NEXT

 
 
 
 
 

Press Here for Answer 

Final Practical Review 

You00e not transmitting CTCSS tone on your radio; Check and correct this no-tone-xmit condition 

  Your ground team calls and urgently tells you they can only hear you when they use their 00onitor00 button  
Why?  

Page Up                    or      NEXT

 
 
 
 
 

Press Here for Answer 

Final Practical Review 

Pull, then move to the right, the EDIT/STep switch 

  00ow do I do that?00nbsp; you ask.  

Page Up                    or      NEXT

 
 
 
 
 

Final Practical Review 

Pull, then move to the right, the EDIT/STep switch 

Use the NEXT switch to toggle around until you find     the selection for TONE control options 

  00ow do I do that?00nbsp; you ask.  

00/font> NEXT00/font> 

Page Up                    or      NEXT

 
 
 
 
 

Final Practical Review 

Use the SELECT switch to turn the TONES ON 

00/font> SELECT00/font> 

Page Up                    or      NEXT

 
 
 
 
 

Final Practical Review 

Use the SELECT switch to turn the TONES ON 

Return the EDIT/STep switch to the Center  

Page Up                    or      NEXT

 
 
 
 
 

Final Practical Review 

Page Up                    or      NEXT 

Return the EDIT/STep switch to the Center  

Use the SELECT switch to turn the TONES ON

 
 
 
 
 

Press Here for Answer 

w  

SC 

Advanced User Training 

  Name the things you need to know before you program a radio channel into this unit  
The Transmit and Receive Frequency  
 

[Page Up]                  or      NEXT 

The Subaudiable tone (CTCSS) required  
 
 

Page Up                    or      NEXT 

Is this channel already programmed in this radio?  
 
 

Page Up                    or      NEXT

 
 
 
 
 

Press Here for Answer 

Final Practical Review 

  What else would it help to know about this channel?  
A name for this channel up to 10 characters long  
 
 

Page Up                    or      NEXT 

SC 

Whether this is to be included in the Scan List  

    

[Page Up                    or      NEXT 

Whether this is a Narrow or Wide Band FM channel  
 

Page Up                    or      NEXT 

w

 
 
 
 
 

Conclusion 

It is hoped that this Advanced User Training will   assist you in the safe and confident operation of  airborne missions using this piece of equipment 

SC 

w  

This concludes Part II, Advanced User Training on the use of  the NPX138N VHF-FM Radio

 
 
 
 
 

end

   download The training program will now resume